OpenBCM V1.07b12 (Linux)

Packet Radio Mailbox

SR1BSZ

[Szczecin_PL JO73GK]

 Login: GUEST





  
G8MNY  > TECH     20.03.24 10:31z 56 Lines 2507 Bytes #-2019 (0) @ WW
BID : 3686_GB7CIP
Read: GUEST
Subj: Simple 20A PS
Path: SR1BSZ<EA2RCF<I0OJJ<GB7CIP
Sent: 240320/1020Z @:GB7CIP.#32.GBR.EURO #:3686 [Caterham Surrey GBR] $:3686_GB
From: G8MNY@GB7CIP.#32.GBR.EURO
To  : TECH@WW

By G8MNY                                     (New Sep 11)
(8 Bit ASCII graphics use code page 437 or 850, Terminal Font)

This is a positive regulator followed by power transistors design. It's a
simple cheap low component count design, but does have drawbacks.

  1/ Unregulated 18-25V needed to give the 3.8V voltage overhead.
  2/ Hazardous exposed unregulated rail voltages on the transistor cases.
  3/ Transistors will get very hot as there is a lot of voltage drop!

BridgeÉÍÍÍÍÍÍÍÍÍËÍÍÍÑÍÍÍÍÍÍÍÍÍÍÍÍËÍÍÍËÍÍÍËÍÍÍËÍÍÍËÍÍÍ»
     / \   100mFº+  ³ ÚÄÄÄÄ¿   ³/  ³/  ³/  ³/  ³/  ³/ 6x
  __/   \__ 30V===  ÀÄ´7815ÃÄÂÄÅÄÄÄÅÄÄÄÅÄÄÄÅÄÄÄÅÄÄÄ´ 2N3055
  ~ \   / ~    Cº     ÀÄÄÂÄÙ ³ ³\e ³\e ³\e ³\e ³\e ³\e
 on  \ /        º    caseÃĴô   o   o   o   o   o   o Soldered
 Case ÈÍÍÍÍÍÍÍÍ͹        ³u1 ³   |   |   |   |   |   | in 3A
                º        ³   ³   o   o   o   o   o   o Fuses
                º        ³  1K   ÈÍÍÍÊÍÑÍÊÍÍÍÊÍÑÍÊÍÍÍÊÍÍÑÍ>+14V
                º        ³   ³    17V _³_    u1³    100u³  @ 20A
                º        ³   ³   Zener/_\'    ===      ===
                º        ³   ³ Crowbar ³       ³    25V ³
 GND>ÄÄÄÄÄÄÄÄÄÄÄÊÍÍÍÍÍÍÍÍÏÍÍÍÏÍÍÍÍÍÍÍÍÍÏÍÍÍÍÍÍÍÏÍÍÍÍÍÍÍÍÏÍ>-VE

AC
The transformer needed is 17V-19V @ 25A for an 20A rated PSU. The high pulse
current AC wiring to bridge & to the reservoir C, should be in thick & twisted
wire to keep the losses & magnetic pulse radiation down.

If the transformer has 2 identical windings (e.g. 2x 13A), consider 2 diode
bi-phase rectifier instead of the single bridge or use 2 bridges, this cuts the
silicon losses & heat down, & enables higher rated PS to be built.

A slow blow mains fuse of 2A should be used.

PSU
The 7815 1A regulator must be mounted on the chassis. it's internal thermal
shutdown (180øC?) & current limiting are used to limit the drive to the 6 low
gain 15A 2N3055s. This ensures they are not over driven to destruction, if a
large heatsink or case is used. Each pass transistor has 3A fuse as the emitter
equalising resistor & identical base & emitter wiring length to ensure all are
given equal drive voltage.

PROTECTION
Off load the PSU voltage will be high, a load R (20R 10W) can be put across the
output to keep this down if important. Voltages over 17V may damage equipment,
so a high power 17V zener is needed, capable of blowing a 3A fuse! Current
peaks & RF will be absorbed by the caps.


Why Don't U send an interesting bul?

73 De John, G8MNY @ GB7CIP


Read previous mail | Read next mail


 28.03.2030 20:27:25zGo back Go up